Mattlatex Farbex - Latex wall paint

Name: Mattlatex Latex wall paint Farbex
Brand: Farbex
SKU: 103
Price: 168.00 UAH
Availability: InStock

Description

Category: Paint

It provides increased hardness and abrasing resistance of the coated surface. It is resistant to intensive repeated washing (resistance to wet abrasion - 1st class according to DSTU EN 13300). It is resistant to weathering and moisture. It provides high surface permeability (according to DSTU EN 1062). It creates a matt finishing coat that completely allows the walls "to breathe". It effectively covers microcracks of the coated surface. It has a high application rate. It is easy to apply. It does not run and spill during application.

Details
Application instruction

Сomposition :

Acrylic latex, pigments, water, extenders, additives.

Color :

white (base A).

Tinting :

It can be tinted manually with Pigment Concentrate Farbex Color, other waterborne coloring pastes or with a coloring machine acc. to NCS color range and others.

Technical data

Consumption standard of 1 layer :

120-150 g/m². Depending on the way of application and the type of surface.

Thinner :

Water. It is allowed to dilute it up to 10% of the total weight of the product.

Application :

It is applied with a roller, a brush or a spraying gun.

Drying period (23 °С, 50% RH) :

maximum 1 hour.The drying period increases as the temperature is getting down and relative air humidity is increasing.

Solids content
(DSTU ISO 3251) :

ab. 61 %

Density (DSTU ISO 2811-1) :

at. 1,54 g/cm³

Gloss (DSTU ISO 2813) :

Maximum 5 GU at 85° (matt, G₃, DSTU EN 1062-1)

Dry film thickness :

50-100 micron, (E₂, DSTU EN 1062-1)

Particle size :

maximum 30 micron, (fine-grained, S₁|, DSTU EN 1062-1)

Vapor permeability (EN ISO 7783-2) :

minimum 150 g/(m²*day), (high, V₁|, DSTU EN 1062-1)

Water permeability (DSTU EN 1062-3) :

maximum 1,0 kg/(m²*h^0,5), (high, W₁|, DSTU EN 1062-1)

Marking acc. to the DSTU EN 1062-1 :

G₃|E₂|S₁|V₁|W₁|A₀|C₀

Wet-scrub resistance, microns (DSTU ISO 11998) :

< 5 (after 200 cycles), 1 class washability (acc. to DSTU EN 13300)

Contrast ratio of dry film (ISO 6504-3) :

min. 98 %, 2 class of hiding power (acc. to DSTU EN 13300)

Warranty period :

24 months

Packaging :

1,4 kg, 4,2 kg, 7 kg, 14 kg, 20 kg

VOC content (ISO 11890) :

-

Application instruction

Surface preparation

Uncoated surface: clean it from fragile surfaces till the hard base surface. Remove dust, oil, grease and other dirt.

Previously coated surface: сlean thoroughly the surface from old loose coats (pealed coats of paint or varnish) in a mechanical (a wire brush or a scraper), thermal (a hot air dryer, infrared radiation) or chemical (paint removing products) ways. Chalk and lime-chalk whitewashes shall be removed till hard surface in a mechanical way. The surface shall be cleaned from different dirt. Surfaces, previously coated with alkyd or oil enamel, shall be sandpapered. After that, treat the surface as the uncoated one.

Non-significant defects of the mineral surface shall be corrected with Finishing Putty TM Farbex. Then sandpaper the surface.

It is recommended to treat the surface with Antiseptic product TM Farbex for protection against mould and fungi.

Priming

Previously treated mineral and wooden surfaces need no undercoating.

Previously untreated absorbing mineral surfaces shall be undercoated with acrylic deep-penetrating primer TM Farbex.

Previously untreated wooden surfaces shall be undercoated with wood protective acrylic primer TM Maxima.

Applying

Stir the paint thoroughly before use. If necessary, dilute it with water. Abnormal dilution makes the quality of the coating worse. Coatins shall be performed at the temperature of the air and the surface under application from +10 ^°С to +30 ^°С and relative air humidity less than 80%. Apply the paint in 1-2 coats with a brush, a roller or a spraying gun.

Do not apply the paint under direct sunlight, strong wind, frost and precipitation. After the coating is applied it shall not be affected with precipitation and sub-zero temperatures for 8 hours.

Tool cleaning

Clean tools with water after application. Do not let them dry. The dry product shall be removed from the tools in a mechanical way.

Sphere of application

It is intended for coating mineral surfaces (plaster, brick, concrete), gypsum and wooden surfaces, wallpapers and fiberglass wallpapers as well as for facades of buildings.

It is recommended for coating of walls and ceilings in dry and wet spaces with high exploitation load and also for surfaces which require high wear-proof property and washability (office and living spaces, hotels, restaurants, shops, medical, infant and educational establishments, public buildings), and also for coating of facades of livings, industrial, administrative, commercial, storing and other buildings.